SBC MT 01 Spécifications télécharger pdf (Page 75)

MT SBC 01

How to cancel the programming of a pushbutton

To cancel a pushbutton and return it to the unprogrammed state

you must:

1. Connect the hand-held programmer to the device to be

programmed, see page 68.

2. Use the and keys to select the Prog. Pushbuttons

menu and then press .

3. Use the and keys to select the pushbutton for which

you want to cancel programming, then press .

4. Use the and keys to select the menu option Reset

Pushbutton, then press .

5. The display will ask you to confirm the operation:

6. Press and make sure that the following message

appears:

- .

If the operation is not successful, the display will show the

message:

7. After a few seconds the display shows the pushbutton selection

menu for any further operations on the extension.

How to programme a default (factory-set) pushbutton

configuration

The configurations of Default pushbuttons (factory-set) are as

follows:

Art. 5714C, 5714CI (see fig. 15 on page 70):

“Transm. failed!”

“Operation OK”

“Transmission OK”

“Reset pushbutton x?”

Sel

Function

Coded Actuator

parameter

35…………….

1. Transmission OK!

2. Operation OK!

Pushbutton 1

Pushbutton 2

Pushbutton 3

OPERATION DISPLAY

Use the

and

keys to

reach the Parameter field and

enter code 35 for the Art. 1256

that you want to activate (N.B.

read the actuator code from the

device’s DIP-switch, see fig. 19).

Use to delete possible

typing errors

Press the key

The display automatically shows

the pushbutton selection menu

for any further operations on the

extension

|<C

k Door lock release

1 Switchboard

2 Switch-on

3 Actuator

4 Actuator

5 Actuator

6 Doctor

Art. 2618 (see fig. 16 on page 70):

Art. 2418W (see fig. 17 on page 70):

Art. 4784 and Art. 4784I (see fig. 18 on page 71):

To programme a default pushbutton configuration you must:

1. Connect the hand-held programmer to the device to be

programmed, see page 68.

2. Use the and keys to select the Prog. Pushbuttons

menu and then press .

3. Use the and keys to select the menu option Default

Cfg then press .

4. The default configuration of the device is displayed.

If necessary, use the and keys to scroll down through

all the pushbuttons. For pushbutton reference information, see

figures 15, 16, 17 and 18 on page 70,71.

5. Press to run pushbutton programming.

6. Make sure that the following message is displayed:

- .

If the operation is not successful, the display will show the

message:

7. After a few seconds the display shows the pushbutton selection

menu for any further operations on the extension.

“Transm. failed!”

“Operation OK”

“Transmission OK”

Sel

k Door lock release

1 Switchboard

2 Switch-on

3 Actuator

4 Privacy

k Door lock release

1 Actuator

2 Switchboard

4 (not programmed)

5 (not programmed)

6 (not programmed)

7 (not programmed)

8 (not programmed)

9 (not programmed)

1 Door lock release

2 Switchboard

3 Privacy

5 (not programmed)

6 (not programmed)

7 (not programmed)

8 (not programmed)

1 2 ... 70 71 72 73 74 75 76 77 78 79 80 ... 131 132

Commentaires sur ces manuels

Pas de commentaire

SBC MT 01 Spécifications Page 75

Commentaires sur ces manuels